| Age | Commit message (Collapse) | Author |
|---|
|
commit d3349b6b3c373ac1fbfb040b810fcee5e2adc7e0 upstream.
syzbot is hitting WARN() triggered by memory allocation fault
injection [1] because loop module is calling sysfs_remove_group()
when sysfs_create_group() failed.
Fix this by remembering whether sysfs_create_group() succeeded.
[1] https://syzkaller.appspot.com/bug?id=3f86c0edf75c86d2633aeb9dd69eccc70bc7e90b
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+9f03168400f56df89dbc6f1751f4458fe739ff29@syzkaller.appspotmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renamed sysfs_ready -> sysfs_inited.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a8690ed6f5346f6738971892205e91d39b6b901 upstream.
In commit 357d23c811a7 ("Remove the obsolete libibcm library")
in rdma-core [1], we removed obsolete library which used the
/dev/infiniband/ucmX interface.
Following multiple syzkaller reports about non-sanitized
user input in the UCMA module, the short audit reveals the same
issues in UCM module too.
It is better to disable this interface in the kernel,
before syzkaller team invests time and energy to harden
this unused interface.
[1] https://github.com/linux-rdma/rdma-core/pull/279
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2ac838e4cd7e5e9891ecc094d626734b0245c99 upstream.
Refactor the validation code used in LOOP_SET_FD so it is also used in
LOOP_CHANGE_FD. Otherwise it is possible to construct a set of loop
devices that all refer to each other. This can lead to a infinite
loop in starting with "while (is_loop_device(f)) .." in loop_set_fd().
Fix this by refactoring out the validation code and using it for
LOOP_CHANGE_FD as well as LOOP_SET_FD.
Reported-by: syzbot+4349872271ece473a7c91190b68b4bac7c5dbc87@syzkaller.appspotmail.com
Reported-by: syzbot+40bd32c4d9a3cc12a339@syzkaller.appspotmail.com
Reported-by: syzbot+769c54e66f994b041be7@syzkaller.appspotmail.com
Reported-by: syzbot+0a89a9ce473936c57065@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b72717a20bba8bdd01b14c0460be7d15061cd6b upstream.
The code was mistakenly using the length of the page array memory instead
of the depth of the page array.
This would cause MR creation to fail in some cases.
Fixes: 8376b86de7d3 ("iw_cxgb4: Support the new memory registration API")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit abe41184abac487264a4904bfcff2d5500dccce6 upstream.
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54836e2d03e76d80aec3399368ffaf5b7caadd1b upstream.
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678f9 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d08338 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678f9 was made we now disable 'packet
mode' before the delay from commit f70893d08338 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678f9 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b697d7d8c741f27b728a878fc55852b06d0f6f5e upstream.
The __get_txreq() function can return a pointer, ERR_PTR(-EBUSY), or NULL.
All of the relevant call sites look for IS_ERR, so the NULL return would
lead to a NULL pointer exception.
Do not use the ERR_PTR mechanism for this function.
Update all call sites to handle the return value correctly.
Clean up error paths to reflect return value.
Fixes: 45842abbb292 ("staging/rdma/hfi1: move txreq header code")
Cc: <stable@vger.kernel.org> # 4.9.x+
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33cc2c9667561b224215e6dfb5bf98e8fa17914e upstream.
The notification of scrub completion happens within the scrub workqueue.
That can clearly race someone running scrub_show() and work_busy()
before the workqueue has a chance to flush the recently completed work.
Add a flag to reliably indicate the idle vs busy state. Without this
change applications using poll(2) to wait for scrub-completion may
falsely wakeup and read ARS as being busy even though the thread is
going idle and then hang indefinitely.
Fixes: bc6ba8085842 ("nfit, address-range-scrub: rework and simplify ARS...")
Cc: <stable@vger.kernel.org>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 313db3d6488bb03b61b99de9dbca061f1fd838e1 upstream.
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bba57eddadda936c94b5dccf73787cb9e159d0a5 upstream.
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 794744abfffef8b1f3c0c8a4896177d6d13d653d upstream.
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1e255d60ae66a9f672ff9a207ee6cd8e33d2679 upstream.
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01b3cdfca263a17554f7b249d20a247b2a751521 upstream.
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd6777 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 367b160fe4717c14a2a978b6f9ffb75a7762d3ed upstream.
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e33eab9ded328ccc14308afa51b5be7cbe78d30b upstream.
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0c4 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 007a74907deeceefef9dc3ec4679fbd7921eaa51 upstream.
The commit 9aaa3b8b4c56 ("thunderbolt: Add support for preboot ACL")
introduced boot_acl attribute but missed the fact that now userspace
needs to poll the attribute constantly to find out whether it has
changed or not. Fix this by sending notification to the userspace
whenever the boot_acl attribute is changed.
Fixes: 9aaa3b8b4c56 ("thunderbolt: Add support for preboot ACL")
Reported-and-tested-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Kellner <christian@kellner.me>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 240630e61870e62e39a97225048f9945848fa5f5 upstream.
There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba44579141f9e2c0229e6e7eeb00b5fa68f0f74a upstream.
This should also be using the default LPM policy for mobile chipsets so
add the PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90d72ce079791399ac255c75728f3c9e747b093d upstream.
Embarrassingly, the recent fix introduced worse problem than it solved,
causing the balloon not to inflate. The VM informed the hypervisor that
the pages for lock/unlock are sitting in the wrong address, as it used
the page that is used the uninitialized page variable.
Fixes: b23220fe054e9 ("vmw_balloon: fixing double free when batching mode is off")
Cc: stable@vger.kernel.org
Reviewed-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa7eee8a143a7e8b530eb1e75fb86cae793d1e21 upstream.
Sometimes when writing large size files to flash in direct/memory mapped
mode, it is seen that flash write enable command times out with error:
[ 503.146293] cadence-qspi 47040000.ospi: Flash command execution timed out.
This is because, we need to make sure previous direct write operation
is complete by polling for IDLE bit in CONFIG_REG before starting the
next operation.
Fix this by polling for IDLE bit after memory mapped write.
Fixes: a27f2eaf2b27 ("mtd: spi-nor: cadence-quadspi: Add support for direct access mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7a020bff31318fc8785e6f96b1d38c1625cf1fb upstream.
This fixes regression introduced by
commit 8d52af6795c0 ("mei: speed up the power down flow")
In power down or suspend flow a message can still be received
from the FW because the clients fake disconnection.
In normal case we interpret messages w/o destination as corrupted
and link reset is performed in order to clean the channel,
but during power down link reset is already in progress resulting
in endless loop. To resolve the issue under power down flow we
discard messages silently.
Cc: <stable@vger.kernel.org> 4.16+
Fixes: 8d52af6795c0 ("mei: speed up the power down flow")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199541
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6edf1d4cb0acde3a0a5dac849f33031bd7abb7b1 upstream.
If the ALL bit is set in the ZBC_OUT command, the command zone ID field
(block) should be ignored.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b320a0a9f23c98f21631eb27bcbbca91c79b1c6e upstream.
The block (LBA) specified must not exceed the last addressable LBA,
which is dev->nr_sectors - 1. So fix the correct check is
"if (block >= dev->n_sectors)" and not "if (block > dev->n_sectords)".
Additionally, the asc/ascq to return for an LBA that is not a zone start
LBA should be ILLEGAL REQUEST, regardless if the bad LBA is out of
range.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d59d2f9995d28974877750f429e821324bd603c7 upstream.
RTL8822be can't bring up properly on ASUS X530UN, and dmesg says:
[ 8.591333] r8822be: module is from the staging directory, the quality
is unknown, you have been warned.
[ 8.593122] r8822be 0000:02:00.0: enabling device (0000 -> 0003)
[ 8.669163] r8822be: Using firmware rtlwifi/rtl8822befw.bin
[ 9.289939] r8822be: rtlwifi: wireless switch is on
[ 10.056426] r8822be 0000:02:00.0 wlp2s0: renamed from wlan0
...
[ 11.952534] r8822be: halmac_init_hal failed
[ 11.955933] r8822be: halmac_init_hal failed
[ 11.956227] r8822be: halmac_init_hal failed
[ 22.007942] r8822be: halmac_init_hal failed
Jian-Hong reported it works if turn off ASPM with module parameter aspm=0.
In order to fix this problem kindly, this commit don't turn off aspm but
enlarge ASPM L1 latency to 7.
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 920c92448839bd4f8eb87a92b08cad56d449caff upstream.
Dan Carpenter reported an integer underflow issue in the rtl8188eu driver.
This is also needed for the length (signed integer) in rtl8723bs, as it is
later converted to an unsigned integer and used in a memcpy operation.
Original issue is at https://patchwork.kernel.org/patch/9796371/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0341fc1981a950c1e902ab901e98f60e0e243f3 upstream.
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25a98edd5795719c5187e16ea271e8de86e02809 upstream.
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa554 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a6b9f4d601dfce8cb68f0dcfd834270280e31e6 upstream.
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc9543 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92748beac07c471d995fbec642b63572dc01b3dc upstream.
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa85015c0d95884c8dc42f38e2f2d6137d436b67 upstream.
After commit 18996f2db918 (ACPICA: Events: Stop unconditionally
clearing ACPI IRQs during suspend/resume) the status of ACPI events
is not cleared any more when entering the ACPI S5 system state (power
off) which causes some systems to power up immediately after turing
off power in certain situations.
That is a functional regression, so address it by making the code
clear the status of all ACPI events again when entering S5 (for
system-wide suspend or hibernation the clearing of the status of all
events is not desirable, as it might cause the kernel to miss wakeup
events sometimes).
Fixes: 18996f2db918 (ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume)
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Thomas Hänig <haenig@cosifan.de>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c83a726d6fbb5d130d8f2edd82a258adb675ac3 upstream.
When the hangcheck handler was replaced by the DRM scheduler timeout
handling we dropped the forward progress check, as this might allow
clients to hog the GPU for a long time with a big job.
It turns out that even reasonably well behaved clients like the
Armada Xorg driver occasionally trip over the 500ms timeout. Bring
back the forward progress check to get rid of the userspace regression.
We would still like to fix userspace to submit smaller batches
if possible, but that is for another day.
Cc: <stable@vger.kernel.org>
Fixes: 6d7a20c07760 (drm/etnaviv: replace hangcheck with scheduler timeout)
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf6ba3aeb2962e5ee4a78e7535af579ecba630bb upstream.
Russell King reported:
"When removing and reloading the etnaviv module, the following splat
occurs:
sysfs: cannot create duplicate filename '/devices/platform/etnaviv'
CPU: 0 PID: 1471 Comm: modprobe Not tainted 4.17.0+ #1608
Hardware name: Marvell Dove (Cubox)
Backtrace:
[<c00157d4>] (dump_backtrace) from [<c0015b8c>] (show_stack+0x18/0x1c)
r6:ef033e38 r5:ee07b340 r4:edb9d000 r3:00000000
[<c0015b74>] (show_stack) from [<c0620784>] (dump_stack+0x20/0x28)
[<c0620764>] (dump_stack) from [<c01bcd24>] (sysfs_warn_dup+0x5c/0x70)
[<c01bccc8>] (sysfs_warn_dup) from [<c01bce14>] (sysfs_create_dir_ns+0x90/0x98)
..."
Commit 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem
DT node") introduced DRM registration via
platform_device_register_simple(), but missed to call
platform_device_unregister() inside etnaviv_exit().
Fix the problem by calling platform_device_unregister() inside
etnaviv_exit(). While at it, also rearrange the function calls
in the exit path to make them happen in the opposite order of
registration.
Tested on a imx6-sabresd board.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45a0faaba9c8c5ba1e31a08a391aed0bad327167 upstream.
platform_device_register_simple() may fail, so we should better
check its return value and propagate it in the case of error.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1376b0a2160319125c3a2822e8c09bd283cd8141 upstream.
There is a '>' vs '<' typo so this loop is a no-op.
Fixes: d35dcc89fc93 ("staging: comedi: quatech_daqp_cs: fix daqp_ao_insn_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79ca484b613041ca223f74b34608bb6f5221724b upstream.
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45f75b8a919a4255f52df454f1ffdee0e42443b2 upstream.
For the word write functions it is retried for error.
But it is not implemented to retry for the erase functions.
To make sure for the erase functions change to retry as same.
This is needed to prevent the flash erase error caused only once.
It was caused by the error case of chip_good() in the do_erase_oneblock().
Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G.
But the error issue behavior is not able to reproduce at this moment.
The flash controller is parallel Flash interface integrated on BCM53003.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85a82e28b023de9b259a86824afbd6ba07bd6475 upstream.
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dbc626597c39b24cefce09fbd8e9dea85869a801 upstream.
Currently device_supports_dax() just checks to see if the QUEUE_FLAG_DAX
flag is set on the device's request queue to decide whether or not the
device supports filesystem DAX. Really we should be using
bdev_dax_supported() like filesystems do at mount time. This performs
other tests like checking to make sure the dax_direct_access() path works.
We also explicitly clear QUEUE_FLAG_DAX on the DM device's request queue if
any of the underlying devices do not support DAX. This makes the handling
of QUEUE_FLAG_DAX consistent with the setting/clearing of most other flags
in dm_table_set_restrictions().
Now that bdev_dax_supported() explicitly checks for QUEUE_FLAG_DAX, this
will ensure that filesystems built upon DM devices will only be able to
mount with DAX if all underlying devices also support DAX.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit 545ed20e6df6 ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15256f6cc4b44f2e70503758150267fd2a53c0d6 upstream.
Add an explicit check for QUEUE_FLAG_DAX to __bdev_dax_supported(). This
is needed for DM configurations where the first element in the dm-linear or
dm-stripe target supports DAX, but other elements do not. Without this
check __bdev_dax_supported() will pass for such devices, letting a
filesystem on that device mount with the DAX option.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Fixes: commit 545ed20e6df6 ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80660f20252d6f76c9f203874ad7c7a4a8508cf8 upstream.
The function return values are confusing with the way the function is
named. We expect a true or false return value but it actually returns
0/-errno. This makes the code very confusing. Changing the return values
to return a bool where if DAX is supported then return true and no DAX
support returns false.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba23cba9b3bdc967aabdc6ff1e3e9b11ce05bb4f upstream.
Change bdev_dax_supported so it takes a bdev parameter. This enables
multi-device filesystems like xfs to check that a dax device can work for
the particular filesystem. Once that's in place, actually fix all the
parts of XFS where we need to be able to distinguish between datadev and
rtdev.
This patch fixes the problem where we screw up the dax support checking
in xfs if the datadev and rtdev have different dax capabilities.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
[rez: Re-added __bdev_dax_supported() for !CONFIG_FS_DAX cases]
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9aa613674f89d01248ae2e4afe691b515ff8fbb6 upstream.
If DMA safe memory was allocated, but the subsequent I2C transfer
fails the memory is leaked. Plug this leak.
Fixes: 8a77821e74d6 ("i2c: smbus: use DMA safe buffers for emulated SMBus transactions")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e03477cb709b73a2c1e1f4349ee3b7b33c50416 upstream.
In i2c_smbus_xfer_emulated(), the function i2c_transfer() is invoked to
transfer i2c messages. The number of actual transferred messages is
returned and saved to 'status'. If 'status' is negative, that means an
error occurred during the transfer process. In that case, the value of
'status' is an error code to indicate the reason of the transfer failure.
In most cases, i2c_transfer() can transfer 'num' messages with no error.
And so 'status' == 'num'. However, due to unexpected errors, it is probable
that only partial messages are transferred by i2c_transfer(). As a result,
'status' != 'num'. This special case is not checked after the invocation of
i2c_transfer() and can potentially lead to unexpected issues in the
following execution since it is expected that 'status' == 'num'.
This patch checks the return value of i2c_transfer() and returns an error
code -EIO if the number of actual transferred messages 'status' is not
equal to 'num'.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f732850df1b2b4d8d719f7e606dfb3050e7ea11 upstream.
Detected on the Dell XPS 9365.
The laptop has 2 devices that benefit from the hid-generic auto-unbinding.
When those 2 devices are presented to the userspace, udev loads both wacom and
hid-multitouch. When this happens, the code in __hid_bus_reprobe_drivers() is
called concurrently and the second device gets reprobed twice.
An other bug in the power_supply subsystem prevent to remove the wacom driver
if it just finished its initialization, which basically kills the wacom node.
[jkosina@suse.cz: reformat changelog a bit]
Fixes c17a7476e4c4 ("HID: core: rewrite the hid-generic automatic unbind")
Cc: stable@vger.kernel.org # v4.17
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 717adfdaf14704fd3ec7fa2c04520c0723247eac upstream.
If our length is greater than the size of the buffer, we
overflow the buffer
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f65245f2d178b9cba48350620d76faa4a098841 upstream.
uref->field_index, uref->usage_index, finfo.field_index and cinfo.index can be
indirectly controlled by user-space, hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/hid/usbhid/hiddev.c:473 hiddev_ioctl_usage() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:477 hiddev_ioctl_usage() warn: potential spectre issue 'field->usage' (local cap)
drivers/hid/usbhid/hiddev.c:757 hiddev_ioctl() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:801 hiddev_ioctl() warn: potential spectre issue 'hid->collection' (local cap)
Fix this by sanitizing such structure fields before using them to index
report->field, field->usage and hid->collection
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef6eaf27274c0351f7059163918f3795da13199c upstream.
Commit ac75a041048b ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a041048b ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9ff68521a5541e1fdaeb0ef11871c035b30e409 upstream.
The other day I was testing one of the HP laptops at my office with an
i915/amdgpu hybrid setup and noticed that hotplugging was non-functional
on almost all of the display outputs. I eventually discovered that all
of the external outputs were connected to the amdgpu device instead of
i915, and that the hotplugs weren't being detected so long as the GPU
was in runtime suspend. After some talking with folks at AMD, I learned
that amdgpu is actually supposed to support hotplug detection in runtime
suspend so long as the OEM has implemented it properly in the firmware.
On this HP ZBook 15 G4 (the machine in question), amdgpu wasn't managing
to find the ATIF handle at all despite the fact that I could see acpi
events being sent in response to any hotplugging. After going through
dumps of the firmware, I discovered that this machine did in fact
support ATIF, but that it's ATIF method lived in an entirely different
namespace than this device's handle (the device handle was
\_SB_.PCI0.PEG0.PEGP, but ATIF lives in ATPX's handle at
\_SB_.PCI0.GFX0).
So, fix this by probing ATPX's ACPI parent's namespace if we can't find
ATIF elsewhere, along with storing a pointer to the proper handle to use
for ATIF and using that instead of the device's handle.
This fixes HPD detection while in runtime suspend for this ZBook!
v2: Update the comment to reflect how the namespaces are arranged
based on the system configuration. (Alex)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4aa5d5eb82bb237d0bb3a38b2a7555054d018081 upstream.
Since it seems that some vendors are storing the ATIF ACPI methods under
the same handle that ATPX lives under instead of the device's own
handle, we're going to need to be able to retrieve this handle later so
we can probe for ATIF there.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99ec9e77511dea55d81729fc80b6c63a61bfa8e0 upstream.
The displaylink hardware has such a peculiarity that it doesn't render a
command until next command is received. This produces occasional
corruption, such as when setting 22x11 font on the console, only the first
line of the cursor will be blinking if the cursor is located at some
specific columns.
When we end up with a repeating pixel, the driver has a bug that it leaves
one uninitialized byte after the command (and this byte is enough to flush
the command and render it - thus it fixes the screen corruption), however
whe we end up with a non-repeating pixel, there is no byte appended and
this results in temporary screen corruption.
This patch fixes the screen corruption by always appending a byte 0xAF at
the end of URB. It also removes the uninitialized byte.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
